Click

 

 

Listed here below you will find lots of awesome insight regarding How to Install a Bathtub Yourself.

Installing a tub isn't specifically rocket science, but it does need strong plumbing, woodworking, and often, tiling abilities. Replacing an old tub with a brand-new one is also a moderately challenging job. If the old bathtub is conveniently obtainable, the task can relocate easily; if you have to open a wall to remove the old bathtub and position the new bathtub, the job is much harder. In either situation, the job is within a residence handyman's abilities, although you will certainly require a helper to move out the old tub and embeded in the brand-new one. See to it you have qualified yourself for the task as well as fit trying it. Rather than hiring a specialist to take over a halfway-completed job, it is better to think about utilizing one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This article will certainly aid you install a new bathtub in your bathroom if you have already bought a new tub as well as don't need to alter the plan of your previous water system pipes.
Your tools and material checklist need to consist of the following:

 

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipe Caps


 

Removing Old Taps

If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you must do is detach the water system. After doing so, switch on the taps to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be rather troublesome due to the limited accessibility that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have been gotten rid of, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from turning during this procedure. As soon as the faucets have been removed, the holes in the bath/basin will need to be cleansed of any old securing substance.
Before proceeding to fit the brand-new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new taps to fit.

 

 

Fitting New Touches

If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and also the other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, then you will call for decreasing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin ensuring that the washing machines remain in place in between the tap as well as the sink. Secure the faucet in position with the producer offered backnut. As soon as the tap is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal faucet ports. The former type should be attached to the faucet ends initially, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.

 

 

Installing the Tub

Making use of the two wooden boards under its feet, position the bathtub in the required placement. The wooden boards are handy in evenly spreading out the weight of the bathtub over the location of the boards rather than concentrating all the weight onto four small factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the spirit level and changing the feet on the bathtub until the level reviews level.
To set up faucets, fit all-time low of the furthest versatile tap adapter to the appropriate supply pipe by making a compression join; after that do the very same for the various other tap.
Turn on the water and also examine all joints and also brand-new pipework for leaks and tighten them if required. Fill up the tub as well as additionally examine the overflow electrical outlet and the normal outlet for leaks.
Lastly, take care of the bathroom paneling as explained in the maker's user's manual. Tiling and also securing around the bath tub should wait until the bathtub has been used at the very least once as this will certainly settle it right into its final setting.

 

 

Preparing for the Setup

Firstly, the sustaining frame supplied with the bathroom ought to be fitted (if needed) according to the manufacturer's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is very important to see to it that if the tap features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets device to stop stress on the tub.
Fit the versatile faucet ports to the bottom of the two taps utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its last placement.

 

 

Tiling Around the Tub

In the area where the bathroom meets the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the fitting can move enough to fracture a rigid seal, causing the water to pass through the wall between the bathroom as well as the tiling, leading to difficulties with moisture and feasible leakages to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to always fill the bathtub with water prior to sealing, to enable the activity experienced when the tub remains in use. The sealer can crack rather early if you do not think about this motion prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly readily available on the market. It is recommended to fit the floor tiles using waterproof or water-proof adhesive as well as cement.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

I'm very involved in How to Install a Bathtub and I really hope you enjoyed reading the entire blog entry. Those who liked our blog posting if you please do not forget to pass it around. I praise you for your time. Come back soon.

Schedule Estimate